V3 description

Update Log

DifferenceDeauther V1Deauther Watch V2Deauther Watch V3

Battery500mah800mah800mah

3D Print CaseYESYESYES

Screen ProtectionNOYESYES

Battery IndicateNOYESYES

Power SwitchPlasticMetalMetal

Charging Current0.5A0.8A0.8A

RTC DS3231NOYESYES

Breakout GPIOsNOYESYES

ColorBlackBlack&WhiteBlack

LaserNONOYES

Work Time3-4h7-8h7-8h

Weight50g61g78g

Size(LxWxH mm)48x39x1755x50x1960x55x22

What is it?

Deauther Watch is still an ESP8266 development board, but you can wear it like a smartwatch.

It comes installed with the latest ESP8266 Deauther software. With this software, you can perform different attacks to test WiFi networks.

Please note that the ESP8266 does only support 2.4GHz.

You can also use it to develop your own software. It is simple to use, just like any other ESP8266 development board.

Function

Deauther Attack: Disconnect 2.4G WiFi

Deauther Beacon: Create fake networks

Deauther Probe:Confuse wifi trackers

Packet Monitor:Display wifi traffic

CLock:Real Time Clock Adjustable

Laser:Powerful Laser can reach 50-100m

GPIOs and Hardware info

Display: SH1106 1.3″ OLED

Display SDA: GPIO 5

Display SCL/SCK: GPIO 4

WS2812b LED: GPIO 15

Button Up: GPIO 12

Button Down: GPIO 13

Button Select: GPIO 14

Laser: GPIO 16

Side Button: GPIO0,RST

Why did you make it?

I designed this development board especially for Spacehuhn’s great project: ESP8266 Deauther. It has been authorized by him and is officially supported.

Thanks to every customer that leaves feedback! I will keep improving this board.

What makes it special?

Only ~80mA power usage

800 mA charging current

Up to around 8-10 hours work time

Arcylic cover and 3D print transparent case

Powerful laser for fun

Indicate charging LED (25%,50%,75%,100%)

Included 5dB FPC antenna

Power Switch (Click to turn on, double click to turn off,long click to open flashlight)

Protection: short, overcharging, over discharging, temperature

Added Extremely Accurate DS3231

Disclaimer

This project is a proof of concept for testing and educational purposes. Neither the ESP8266, nor its SDK was meant or built for such purposes. Bugs can occur!

Use it only against your own networks and devices! Please check the legal regulations in your country before using it. We don’t take any responsibility for what you do with this program.

More Info

Deauth

Closes the connection of WiFi devices by sending deauthentication frames to access points and client devices you selected. This is only possible because a lot of devices don’t use the 802.11w-2009 standard that offers a protection against this attack. Please only select one target! When you select multiple targets that run on different channels and start the attack, it will quickly switch between those channels and you have no chance to reconnect to the access point that hosts this web interface.

Beacon

Beacon packets are used to advertise access points. By continuously sending beacon packets out, it will look like you created new WiFi networks. You can specify the network names under SSIDs.

Probe

Probe requests are sent by client devices to ask if a known network is nearby. Use this attack to confuse WiFi trackers by asking for networks that you specified in the SSID list. It’s unlikely you will see any impact by this attack with your home network.

Videos

Software 2.6.0 Introduction

DSTIKE Deauther Watch V3 Quick Video

How do I assemble deauther watch V3

How to install antenna of deauther watch

How to increase the maximum effect of antenna

How to connect smart phone

DSTIKE Deauther Watch Demo

NTP Time server functions

How to install DSTIKE Arduino environment

How to use 8266 flash tool flash deauther firmware

SE version description

UPDATE LOG

DifferenceDeauther Watch SEDeauther Watch V3Deauther Watch V4

Battery500mah800mah1000mah

3D Print CaseYESYESYES

Screen ProtectionYESYESYES

Battery Life IndicateNOYESYES

Charging IndicateYESYESYES

Power SwitchPlasticMetalMetal

Charging Current0.5A0.8A0.8A

RTC DS3231YESYESYES

Breakout GPIOsYESYESYES

ColorBlackBlackBlack

Standby currentLowMediumMedium

LaserNOYESNO

BuzzerYESNONO

StrapSoft sillica gelNylonSoft sillica gel

Work Time3-4h7-8h8-10h

Weight60g70g90g

Size(LxWxH mm)60x42x2260x55x2280x60x22

WHAT IS IT?

Deauther watch SE has redesigned surface and circuit. RTC could work for several months after you turn off the watch. You can also flash deauth detector software because it has buzzer now.

Deauther Watch is still an ESP8266 development board, but you can wear it like a smartwatch.

It comes installed with the latest ESP8266 Deauther software. With this software, you can perform different attacks to test WiFi networks.

Please note that the ESP8266 does only support 2.4GHz.

You can also use it to develop your own software. It is simple to use, just like any other ESP8266 development board.

FUNCTION

Deauther Attack: Disconnect 2.4G WiFi

Deauther Beacon: Create fake networks

Deauther Probe:Confuse wifi trackers

Packet Monitor:Display wifi traffic

GPIOS AND HARDWARE INFO

Display: SH1106 1.3″ OLED

Display SDA: GPIO 5

Display SCL/SCK: GPIO 4

WS2812b LED: GPIO 15

Button Up: GPIO 12

Button Down: GPIO 13

Button Select: GPIO 14

Buzzer: GPIO 0

Side Button: RST

WHY DID YOU MAKE IT?

I designed this development board especially for Spacehuhn’s great project: ESP8266 Deauther. It has been authorized by him and is officially supported.

Thanks to every customer that leaves feedback! I will keep improving this board.

WHAT MAKES IT SPECIAL?

Double Arcylic Protection

Transparent Case

Soft sillica gel strap

500 mA charging current

Indicate charging LED (RED will turn off when full)

ESP12F Inside

Power Switch

Protection: short, overcharging, over discharging, temperature

DISCLAIMER

This project is a proof of concept for testing and educational purposes. Neither the ESP8266, nor its SDK was meant or built for such purposes. Bugs can occur!

Use it only against your own networks and devices! Please check the legal regulations in your country before using it. We don’t take any responsibility for what you do with this program.

MORE INFO

Deauth

Closes the connection of WiFi devices by sending deauthentication frames to access points and client devices you selected. This is only possible because a lot of devices don’t use the 802.11w-2009 standard that offers a protection against this attack. Please only select one target! When you select multiple targets that run on different channels and start the attack, it will quickly switch between those channels and you have no chance to reconnect to the access point that hosts this web interface.

Beacon

Beacon packets are used to advertise access points. By continuously sending beacon packets out, it will look like you created new WiFi networks. You can specify the network names under SSIDs.

Probe

Probe requests are sent by client devices to ask if a known network is nearby. Use this attack to confuse WiFi trackers by asking for networks that you specified in the SSID list. It’s unlikely you will see any impact by this attack with your home network.

VIDEOS

Software 2.6.0 Introduction

How to connect smart phone

DSTIKE Deauther Watch Demo

NTP Time server functions

How to install DSTIKE Arduino environment

How to use 8266 flash tool flash deauther firmware

V3S description :

What is it?

Deauther Watch V3S is the updated version of the old V3. With the latest Deauther software, you can perform various attacks to test WiFi networks. Please note that ESP8266 only supports 2.4GHz frequency. Additionally, you can utilize it for developing your own software. It is user-friendly and operates similar to any other ESP8266 development board.

Upgrade Log

WiFi chip upgraded from 1MB ESP07s to 4MB DSTIKE ESP07.

Watch strap upgraded from knitted strap to silicone strap.

Battery upgraded from 800mAh to 1000mAh.

USB upgraded from Micro USB to Type-C.

Indicator LEDs have been removed to eliminate annoyance.

Laser has been removed.

An external SMA connector has been added.

Introducing a new power supply solution that allows for power on/off by pressing for 3 seconds.

Function

Deauther Attack: Disconnect 2.4G WiFi

Deauther Beacon: Create fake networks

Deauther Probe: Confuse WiFi trackers

Packet Monitor: Display WiFi traffic

Clock: Real Time Clock Adjustable

GPIOs and Hardware info

Display: SH1106 1.3″ OLED

Display SDA: GPIO 5

Display SCL/SCK: GPIO 4

WS2812b LED: GPIO 15

Button Up: GPIO 12

Button Down: GPIO 13

Button Select: GPIO 14

Bright LED: GPIO 16

Side Button: Power and Reset

Why did you make it?

I designed this development board especially for Spacehuhn’s great project: ESP8266 Deauther. It has been authorized by him and is officially supported. Thanks to every customer that leaves feedback! I will keep improving this board.

Package Included

1 x DSTIKE Deauther Watch V3

1 x Typec Power/Data cable

1 x Arcylic Cover board

1 x Software manual

Disclaimer

This project serves as a proof of concept for testing and educational purposes. It is important to note that neither the ESP8266 nor its SDK were intended or developed for such purposes. As a result, bugs may occur. Please ensure that you only use this project against your own networks and devices. Prior to usage, it is essential to review and comply with the legal regulations pertaining to your country. We do not accept any responsibility for any actions taken with this program.

More Info

Deauth

The deauthentication feature is designed to close the connection of WiFi devices by sending deauthentication frames to the selected access points and client devices. It’s important to note that this attack is only possible because many devices do not implement the 802.11w-2009 standard, which provides protection against such attacks.

To ensure proper usage, please select only one target at a time. If you select multiple targets running on different channels and initiate the attack, the system will rapidly switch between those channels, making it difficult to reconnect to the access point hosting the web interface.

Beacon

Beacon packets are used to advertise access points. By continuously sending beacon packets out, it will look like you created new WiFi networks. You can specify the network names under SSIDs.

Probe

Probe requests are sent by client devices to ask if a known network is nearby. Use this attack to confuse WiFi trackers by asking for networks that you specified in the SSID list. It’s unlikely you will see any impact by this attack with your home network.

Here I post a few quick links:

Software https://github.com/SpacehuhnTech/esp8266_deauther

Hardware https://github.com/lspoplove/Deauther-Project

WiKi https://github.com/SpacehuhnTech/esp8266_deauther/wiki

FAQ https://github.com/SpacehuhnTech/esp8266_deauther/wiki/FAQ

Burning tutorial https://github.com/SpacehuhnTech/esp8266_deauther/wiki/Installation

Burning tool https://github.com/nodemcu/nodemcu-flasher

Firmware download https://github.com/SpacehuhnTech/esp8266_deauther/releases

Please Check out the how-to video link :

Quick product upgrade tutorial:

1. Download CP2102 driver (https://www.silabs.com/products/development-tools/software/usb-to-uart-bridge-vcp-drivers)

2. Download the firmware (https://github.com/SpacehuhnTech/esp8266_deauther/releases)

3. Download nodemcu-flasher (https://github.com/nodemcu/nodemcu-flasher)

4. Click the gear to select the corresponding binfile. The programming mode selects DOUT. The rate selects 961200. Click Flash start and wait for the progress bar to reach the end and then power on

Search Deauther on Github to find the corresponding project. On Github, we have put YouTube video links, WiKi, FAQ, etc., which can basically solve 90% of your problems. You can check the issues of this project for the remaining 10%. You can ask questions in the issues, or you can View answers to the same questions asked by others

Deauther Watch is still an ESP8266 development board, but you can wear it like a smart watch.

I provide 3D print case only for Deauther Watch.

But I do not provide case for old Deauther Wristband.

3D Print Case Download:

https://github.com/lspoplove/Deauther-Project/blob/master/3DPrint/DeautherWatch.STL

Assemble Video

https://youtu.be/-aw1laQx-1c

It comes installed with the latest ESP8266 Deauther software. With this software, you can perform different attacks to test WiFi networks.

Please note that the ESP8266 does only support 2.4GHz. For more details on the software, visit here.

https://github.com/spacehuhn/esp8266_deauther

You can also use it to develop your own software. It is simple to use, just like any other ESP8266 development board.

GPIOs and hardware info

Display SH1106 1.3 OLED

Display SDA GPIO 5 (D1)

Display SCL/SCK GPIO 4 (D2)

WS2812b LED GPIO 15 (D8)

Button Up GPIO 12

Button Down GPIO 13

Button Select GPIO 14

High Light LED GPIO 16

Side Button GPIO0 GPIO2 RST

Please use computer to see more details

Deauther Watch V2 fixed all the problems I collected. Now hardware has RTC but software will update later. ESP32 does not support deauther.

Update Log

DifferenceDeauther WristbandDeauther Watch V1Deauther Watch V2

Battery500mah500mah800mah

3D Print CaseNoYESYES

Screen ProtectionNoNoYES

Battery IndicateNoNoYES

Power SwitchPlasticPlasticMetal

Charging Current0.5A0.5A0.8A

RTC DS3231NoNoYES

Breakout GPIOsNoYESYES

ColorBlack&RedBlack

Black&White

What is it?

Deauther Watch is still an ESP8266 development board, but you can wear it like a smartwatch.

This ESP8266 development board comes with a 800mAh battery, OLED display and a 3-way momentary slide switch.

It comes installed with the latest ESP8266 Deauther software. With this software, you can perform different attacks to test WiFi networks.

Please note that the ESP8266 does only support 2.4GHz. For more details on the software, visit here.

You can also use it to develop your own software. It is simple to use, just like any other ESP8266 development board.

GPIOs and hardware info

Display: SH1106 1.3″ OLED

Display SDA: GPIO 5 (D1)

Display SCL/SCK: GPIO 4 (D2)

WS2812b LED: GPIO 15 (D8)

Button Up: GPIO 12

Button Down: GPIO 13

Button Select: GPIO 14

High Light LED: GPIO 16

Side Button: GPIO0,RST

Why did you make it?

I designed this development board especially for Spacehuhn’s great project: ESP8266 Deauther. It has been authorized by him and is officially supported.

Thanks to every customer that leaves feedback! I will keep improving this board.

What makes it special?

Only ~80mA power usage

Up to around 8-10 hours work time

800 mA charging current

Indicate charging LED (25%,50%,75%,100%)

Included 5dB FPC antenna and 2dB antenna

Power Switch (Click to turn on, double click to turn off)

Protection: short, overcharging, over discharging, temperature

Added Extremely Accurate DS3231

Disclaimer

Use it only for testing and educational purposes against your own devices! I don’t take responsibility for what you do with it.

Please check the legal regulations for your country to make sure you don’t violate any laws.

You can get full information from WiKi

Assemble Video

Scehmatic and 3D Print Design files

RTC Test

What is it?

I call it D&B watch. It is a Deauther & Bad USB watch. You can also call it deauther watch V4. You can look Deauther Watch V3 to understand what is deauther.

Why did you make it?

In order to make it more fun. I added atmega32u4(Arduino Leonardo) to this watch. Now this watch not only disconnect wifi but also perform bad usb attack!

What makes it special?

Compare to deauther watch V3:

ESP07 changed to ESP07s: With an external 3dB antenna it could search more signal than V3. You can also add bigger antenna to the SMA connector.

Added Atmega32u4: I flashed Arduino Leonardo bootloader already. You can program it as bad usb directly.Two buttons(Digital pin 9 and 10) could be used to execute different commands. I flashed a demo program. When bad usb port connects PC, press DP9 button cmd window will be opened. Press DP10 button Notepad will be opened. You can reprogram it via Arduino IDE.

Bridge: There are empty solder pads at the back of this watch. You can solder them to connect ESP8266 with atmega32u4. For example if you solder IIC pads this watch could become wifi duck.

Battery: 800mAh battery upgrade to 1000mAh. There are more space inside to put bigger battery instead.

Strap: Canvas strap upgrade to silicone strap.

Design: 3D case has been redesigned. Added bottom arcylic board to pretect this watch.

Charging: There are two usbs. Each usb could be used to charge battery. But I do not suggest you use them at the same time.

Deauther Watch SE

Descripiton

DifferenceDeauther Watch SEDeauther Watch V3Deauther Watch V4

Battery500mah800mah1000mah

3D Print CaseYESYESYES

Screen ProtectionYESYESYES

Battery Life IndicateNOYESYES

Charging IndicateYESYESYES

Power SwitchPlasticMetalMetal

Charging Current0.5A0.8A0.8A

RTC DS3231YESYESYES

Breakout GPIOsYESYESYES

ColorBlackBlackBlack

Standby currentLowMediumMedium

LaserNOYESNO

BuzzerYESNONO

StrapSoft sillica gelNylonSoft sillica gel

Work Time3-4h7-8h8-10h

Weight60g70g90g

Size(LxWxH mm)60x42x2260x55x2280x60x22

WHAT IS IT?

Deauther watch SE has redesigned surface and circuit. RTC could work for several months after you turn off the watch. You can also flash deauth detector software because it has buzzer now.

Deauther Watch is still an ESP8266 development board, but you can wear it like a smartwatch.

It comes installed with the latest ESP8266 Deauther software. With this software, you can perform different attacks to test WiFi networks.

Please note that the ESP8266 does only support 2.4GHz.

You can also use it to develop your own software. It is simple to use, just like any other ESP8266 development board.

FUNCTION

Deauther Attack: Disconnect 2.4G WiFi

Deauther Beacon: Create fake networks

Deauther Probe:Confuse wifi trackers

Packet Monitor:Display wifi traffic

GPIOS AND HARDWARE INFO

Display: SH1106 1.3″ OLED

Display SDA: GPIO 5

Display SCL/SCK: GPIO 4

WS2812b LED: GPIO 15

Button Up: GPIO 12

Button Down: GPIO 13

Button Select: GPIO 14

Buzzer: GPIO 0

Side Button: RST

WHY DID YOU MAKE IT?

I designed this development board especially for Spacehuhn’s great project: ESP8266 Deauther. It has been authorized by him and is officially supported.

Thanks to every customer that leaves feedback! I will keep improving this board.

WHAT MAKES IT SPECIAL?

Double Arcylic Protection

Transparent Case

Soft sillica gel strap

500 mA charging current

Indicate charging LED (RED will turn off when full)

ESP12F Inside

Power Switch

Protection: short, overcharging, over discharging, temperature

DISCLAIMER

This project is a proof of concept for testing and educational purposes. Neither the ESP8266, nor its SDK was meant or built for such purposes. Bugs can occur!

Use it only against your own networks and devices! Please check the legal regulations in your country before using it. We don’t take any responsibility for what you do with this program.

MORE INFO

Deauth

Closes the connection of WiFi devices by sending deauthentication frames to access points and client devices you selected. This is only possible because a lot of devices don’t use the 802.11w-2009 standard that offers a protection against this attack. Please only select one target! When you select multiple targets that run on different channels and start the attack, it will quickly switch between those channels and you have no chance to reconnect to the access point that hosts this web interface.

Beacon

Beacon packets are used to advertise access points. By continuously sending beacon packets out, it will look like you created new WiFi networks. You can specify the network names under SSIDs.

Probe

Probe requests are sent by client devices to ask if a known network is nearby. Use this attack to confuse WiFi trackers by asking for networks that you specified in the SSID list. It’s unlikely you will see any impact by this attack with your home network.

VIDEOS

Software 2.6.0 Introduction

How to connect smart phone

DSTIKE Deauther Watch Demo

NTP Time server functions

How to install DSTIKE Arduino environment

How to use 8266 flash tool flash deauther firmware

DSTIKE D&B Watch (V4)

Deauther Watch SE

Seguir explorando la tienda

Mas información sobre  Reloj inteligente